Hornady’s SUB-X bullets are optimized for expansion at subsonic velocities. How well will these bullets perform for 300 AAC Blackout? That’s the question we’ll answer in this story!
Disclaimer
Ultimate Reloader LLC / Making with Metal Disclaimer: (by reading this article and/or watching video content you accept these terms)
- The content on this website (including videos, articles, ammunition reloading data, technical articles, gunsmithing and other information) is for demonstration purposes only.
- Do not attempt any of the processes or procedures shown or described on this website.
- All gunsmithing procedures should be carried out by a qualified and licensed gunsmith at their own risk.
- Do not attempt to repair or modify any firearms based on information on this website
- Ultimate Reloader, LLC and Making With Metal can not be held liable for property or personal damage due to viewers/readers of this website performing activities, procedures, techniques, or practices described in whole or part on this website.
- By accepting these terms, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this website.
About Hornady SUB-X Bullets
From the Hornady SUB-X product page:
Reliable subsonic expansion
Sub-X® (Subsonic — eXpanding) bullets deliver big results without a big bang! Designed to provide deep penetration below the speed of sound, Sub-X® features a lead core. Long grooves in its gilding metal jacket combine with its flat profile and the patented Flex Tip® insert within the bullet’s hollowpoint cavity to help it expand reliably at low velocities. Cannelures provide positive case crimp, making Sub-X® ideal for semiautomatic weapons.
EXPANDS AT SUBSONIC VELOCITIES
Patented Flex Tip® technology aids in expansion at velocities as low as 900 fps.
PROVEN PERFORMANCE
Meets FBI protocol for terminal ballistic test requirements.
POSITIVE CASE CRIMP
Lead core bullet with cannelured jacket provides positive case crimp for use in semiautomatics.
WIDE RANGE OF GUNS
Designed to fit, feed and function in a variety of firearms, including gas system guns.
Loading Setup and Data
This ammunition was loaded on theHornady Lock-N-Load AP 5-station progressive reloading press:
For die stations, above we have:
- Sizing (expander ball only, new brass)
- Priming (bottom), no die used (top)
- Powder charge
- Bullet seat (I showed at station #5 in the video)
- empty
You’ll also want to check out the KMS Squared UFO press light, this thing works GREAT!
Here you can see I’m using an Inline Fabrication Quick Change Ultramount as well!
Load Components and Data
Above: the components used for loads tested in this story:
- Bullets: Hornady 190 grain 30 caliber SUB-X, Midsouth Match Monster 190 grain 30 caliber
- Brass: New Federal American Eagle 300 Blackout
- Powder: Hodgdon CFE-BLK, 12.0 grains
- Primer: Federal 205 Small Rifle
Load Disclaimer
Use load data at your own risk. Ultimate Reloader is not responsible for errors in load data on this website. Always cross-reference load data with manufacturer’s published data.
300 Blackout Full-Auto AR-15
The rifle used in this story is a “special custom” full-auto AR-15. Note: Ultimate Reloader is a Type 07 Firearms Manufacturer (FFL) and Class 2 SOT, otherwise this would be illegal.
Some information about the rifle follows:
Upper:
Anderson ManufacturingAR-15 300 Blackout Upper:
- 16″ Carbine length barrel, 1:8 twist
- Carbine length gas setup
Lower:
- Aero Precision M4E1 FDE lower receiver modified to accept M16-style fire control group (safe, semi, auto)
- M16 fire control group
- Magpul MOE SL-K collapsible buttstock
- Magpul MOE Plus rubber grip
For this story, I’m using a SilencerCo Hybrid 46 caliber suppressor.
About Clear Ballistics Gel
We use Clear Ballistics Gel to determine bullet expansion and penetration. While synthetic ballistics gelatin will not 100% reflect what a bullet will do to a human or animal, it provides us with valuable data and allows us to compare the performance of different bullets and different loads.
American-made Clear Ballistics Gel is reusable. It can be melted down and utilized again for even more tests. Consult ClearBallistics.com to view all of their offerings!
190 grain Match Monster 300 BLK Performance
First up was the 190 Match Monster load which I’ve used previously. This load and bullet is GREAT for shooting steel targets, but I had to know how they would do with ballistics gel.
This load produced an average velocity of 1014.8 feet/sec which is a nice velocity for subsonic scenarios.
When we went to shoot this load with the Clear Ballistics gel, things didn’t exactly go as planned! Here’s the shot by shot breakdown:
- Shot 1: Went through the entire single block (only one setup for this shot)
- Shot 2: (two blocks) Penetrated first block and part of second block, emerging from top of block
- Shot 3: (two blocks) Same result as Shot 2, but emerging from the side
I was able to find the bullet from shot 3 laying on the ground- following a path along the ground at the angle which the ballistics gel suggested the bullet was travelling as it exited the gel. Amazing.
As you can see in the picture above, the bullet looked to be in very good condition, the only obvious thing was the rifling marks engraved on the bearing surface of the bullet. A quick test on the scale showed the weight at 190.84 grains, most likely exactly what the bullet weighed before striking the ballistics gel.
190 grain SUB-X 300 BLK Performance
And then came the test I was waiting for! I saw how the Match Master bullets performed in ballistics gel, now to compare with a bullet specifically designed for subsonic expansion: the SUB-X!
This load chronographed FASTER than the Match Master with the same weight (190 grains) and same powder charge (12.0 grains CFE-BLK). Average velocity was measured at 1088.6 feet/sec which is perfect for “max performance *and* subsonic”.
You can see the difference in “wound channel” between the 190 HPBT standard bullet and the Sub-X- it’s pretty dramatic! And here’s the “sonoluminescence” as the cavity collapsed, and before the bullet “bounced back” to its final resting place:
Then came the extraction of the bullet, which penetrated to a depth of 17″ (1″ into the second gel block):
The SUB-X bullet expanded very nicely, with perfect symmetry, and no apparent loss of material:
Here’s how the numbers looked:
- Base diameter: 0.307″, Expanded diameter: 0.463″ (51% expansion)
- 187.94 retained weight (99% weight retention)
Now that’s some great performance! I can’t wait to see how these bullets will perform on varmints around the ranch! Would I use this rifle and ammunition for home defense? YES.
A Note about Magazines
There’s one thing about the 300 Blackout that you need to be prepared for: magazines are sometimes an issue. With 300 Blackout cartridges having such a different “profile”, this is not too much of a surprise. I noticed during the filming of the video for this story that the flat-nosed profile of the SUB-X bullets can cause feeding issues with some magazines.
Consider the steel AR-15 magazine here next to a Magpul P-Mag 20, both loaded with SUB-X ammunition:
If you look closely at the front cut, you’ll notice how much lower the cut is on the P-MAG compared to the steel magazine. This helps significantly with feeding. The flat points of the SUB-X bullets can “hit the wall” on magazines without this low cut (as pictured at right). One of the things I’m looking at is Magpul’s “PMAG M3 300 B Magazine” which is optimized for 300 Blackout subsonic cartridges. We’ll have to see if that helps things out at all!
Get the Gear
- Clear Ballistics Gel
- Hornady Lock-N-Load AP 5-station progressive reloading press
- Inline Fabrication Quick Change Ultramount
- Hornady 190 grain 30 caliber SUB-X Bullets
- Midsouth Match Monster 190 grain 30 caliber Bullets
- Hodgdon CFE-BLK Powder
- Federal 205 Small Rifle Primers
- KMS Squared UFO press light
- Inline Fabrication Ultramount with Quick change
Don’t miss out on Ultimate Reloader updates, make sure you’re subscribed!
Thanks,
Gavin